Monday, August 31, 2009

Week 2

During the week 2 of the LTT training, we have done a couple of projects.

Riveting Layout
First up is the Riveting Layout assignment. Remember the Scribe and Punch exercise I mentioned in the first week? We did something similar to it except that we drill holes on those markings!
The objective of this exercise is to help us learn the techniques of drilling a hole using a hand drill.
We had to use this on the vice clamp as the material is aluminium and it is soft. Not using that magnetic clamp to support will damage the workpiece when clamped onto the vice.

We pre drilled the first piece with a 2.5 mm drill bit and we later clamped the 2nd workpiece underneath the first!

Toggle clamps were used to clamp more than 1 workpiece together tightly!

Files were still widely used to file the workpiece to size and squaring of sides!

Handrill and the drill bits were the main tools in this exercise!
It is important to keep the drill perpendicular to the workpiece while drilling to ensure that the hole drilled is straight!

After the markings were done. We are all good to go!

After the holes were drilled, we are still missing something!

It is important to remove all burs after drilling! Excess burrs can be dangerous as they are sharp and can cause injuries easily!

This is the final product!

Sawing Exercise
Next up will be the sawing exercise which is a 1 day exercise!

In this sawing exercise, we will be introduced to the techniques of cutting material using a hacksaw! The hacksaw is an easy tool to use if the proper techniques are used. The saw only cuts in the forward or backward stroke depending on the teeth on the saw. So strength is only to be applied on either stroke depending if the saw is forward cut or vice versa.



The tool that does it all! Hacksaw!

We were given a steel workpiece which we must do markings and dot punch before sawing. The reason we dot punch the workpiece is to remind us that we are sawing close to the line in order to maintain the correct measurements.



We start from scratch from a steel workpiece.

After all the markings were done...

We are to saw 4 shapes out of the workpiece!

And filing them to the dimensions required!

Chisel Exercise
The last exercise done in week 2 is chiseling. It is a simple exercise while let have a feel of the chisel tool. The chisel tool is accompanied by a hammer. It is another way to cutting material but usually used on soft materials like aluminium.



The chisel is the one on the extereme right!

Is usually accompanied by a hammer to get the job done!

A nice spiral shape appearing if the chisel is done at constant speed!

The final product!!!

Well.. Here comes the fun part once again! What we actually do in the workshop!

We are good students! We listen to Mr Zahir during briefing so we are always clear of what to do!

It is important to ensure that the workpiece is square and flat at all times!

Deburring is no easy task man!!!

100% concentration given during training at all times!!!

NO HORSEPLAYING IN THE WORKSHOP! Don't worry! We are just posing for a picture. ^^

-PeRrY-

Sunday, August 30, 2009

Week 1 (U Block, Scribe & Punch)

During the week 1 of LTT training, we have learned 2 basic skills by doing 2 exercises assigned. First one was filing an U block followed by Scribe and Punch!

The first 3 days was spent doing filing as filing is the most basic skill we must master as any projects we need to do will require us to file first! Filing may seem like a child's play but in order to file straight and even throughout the surface, it takes a lot of skills and practice. Learning proper filing techniques also allows us to work more efficiently and prevent uncessary injuries!

We were given this material and are required to file to the specific dimension with a little tolerance and file off the rust for a shiny and smooth surface.

There are some problems we faced during the U Block project. Firstly, the material is mild steel, it is very hard to remove a lot of material at once. Hence, the process is slow and tedious! We also need to be very careful with the dimensions as we may file and file without measuring and therefore the workpiece will be undersized. The tolerance is for us to compensate if we make any mistakes. Deburring the workpiece is also crucial as there are sharp edges and may cause injuries if not properly handled. So deburring the workpiece will reduce the risk of cutting ourselves.

After 3 days of filing and more filing...

There you have it! A shiny smooth finish on the U Block! Compared to the U Block 3 days ago, we feel a sense of achievement behind able to remove almost 100% of the rust! Trust me. This is not child's play after all!

Our next assignment for the first week is Scribe & Punch. We will be introduced to two new tools in this assignment. One is the scriber and the second are the number and alphabet punches to engrave on our workpiece. The scriber is an essential tool for us as it is used to do markings on the workpiece so as to minimise errors while drilling or punching on the workpiece.

There are also techniques to dot punching! It has first to be aligned with the scriber or pencil marking and then held perpendicular to the workpiece before being hammered.

This is the completed Scribe & Punch project!

The problems faced in this project are rather minor and can be solved easily. Firstly, scribing the material too hard may expose too much of the raw material and may cause it to be oxidised. Secondly, dot punching the material too hard may cause a dent at the opposite side and it can be avoided by using adequate strength to dot punch the workpiece. Using not enough strength is also a problem as the mark may not be seem and punching over it a second time may produce another seperate mark which is unpresentable. Number/Alphabet punching also require skills are each has to be spaced equally apart and straight. If students are not careful, they may have letters floating around and may not look presentable.

Next I will introduce to some of the tools we used for the first 2 assignments!

The mother of all assignments! Files!!! We have the file flat, round file, half round file, triangular file, square file!

Brushes! These brushes are essential to keep the working environment safe and clean!

Set Squares! This tool enables us to get measure and get a perfecr 90 degrees so we can ensure if our workpiece is even throughout the surface.

Vernier Caliper! This is a precision measuring tool and it enables us to do measurements up to .05 mm of accuracy! We can also measure depth, circumference and do marking with this tool!


Dot Punch! This is a tool for us to do marking on materials!

The Hacksaw enables us to cut away excess materials!

The hammer allows us to do dot punching and alphabet/number punching!

I have typed a whole chunk of words on top. Now let me show you guys what I really mean!

The process...

The file is flat on the surface!

Standing at an angle helps to prevent injuries and it ease the filing process!

Applying force on the forward stroke is the correct technique displayed. No force is required while returning the file as the file cuts only on the forward stroke.

Who says only guys can do it?!?!

The scriber is your greatest weapon!
The file is your greatest enemy!

Finally... Let me share the outcome of our first 2 assignments!!!

We do have some artistic talent there yea?!?! =)

The few of us looking so happy and satisfied after the first week of LTT!!

-PeRrY-

Lufthansa Technical Training

The first day of LTT is full of excitment for us. Why? Simply because we will be exposed to a whole semester of training and not the usual lectures and tutorials we have been going through. We are exposed to more hands on experience during the duration of the training. This is beneficial to us as we can apply what we learn during theory lessons and put good use during practical lessons and allow us to explore the possibilities of solving our own problems if faced.

During our stay in Lufthansa Technical Training (LTT), we will learn the tecnical skills required to repair and maintainance aircrafts. This is the basic training we are required to fufuil and we are very fortunate to be students of Temasek Polytechnic (TP) as LTT set up in TP and students get to enjoy the best facilities and learning environment to trigger our thoughts.

Here let me show you guys some photos of what facilities LTT have got to offer!!!

We have the tools store for students to borrow required tools for our projects! All tools and materials are the actual stuffs used on the aircraft too! For example, the Hi-Loks, Helicoils etc are the same installed on the aircraft!

This is the electrical room for students to learn about electrical cables and wires!

We have a riveting shop for students to do riveting as the noise produced while doing riveting is great! So students doing it in the shop will reduce the noise greatly so as not to distract other students!

There is a composite shop for students to do composite repair just like the real deal done to the aircraft!!!

We have 12 work benches and each bench is installed with 6 vice clamp and are fully equiped with 4 drawers of tools!!!

A bench saw to saw awkward shapes!

2 bending machines to do bending exercises and projects!

Shearing machine to cut off materials!

Hand washing time!!! 5 taps fully equiped with soap for removal of dirt after work!

Feeling thirsty?!? Fear not! There's even a water cooler for students to enjoy!

We are environmentally friendly too! These 2 bins are for scrap materials to recycle!

Ain't we fortunate being part of the LTT program? I personally did not regret at all choosing the Aerospace Engineering Option!

By the end of the training, this will be the projects that we have done! This are the projects done by the last batch of LTT students and we will be doing the same too!

-PeRrY-